Is your prop too big or too small?
By Propbench · updated 19 November 2026Full-throttle rpm tells you. Run the boat at full throttle (wide-open throttle, or WOT) with a normal load and read the rpm. If the engine stays under the maker's recommended range, the prop is too big: it has too much pitch. If the engine runs past the range or hits the rev limiter, the prop is too small. One inch of pitch moves full-throttle rpm by about 150–200 rpm.
Too big or too small: the signs
A prop that is too big is called overpropped. One that is too small is underpropped. These are the usual signs.
| Too big (overpropped) | Too small (underpropped) | |
|---|---|---|
| Full-throttle rpm | Under the recommended range | Above the range, or on the rev limiter |
| Getting onto the plane | Slow; the engine labours | Quick |
| Top speed | Lower: the engine can’t reach the rpm where it makes full power | Lower: the engine reaches its top rpm at a slower speed |
| What it costs | Strain and wear on the engine | Over-revving, which can damage the engine |
Sources: Boating Magazine on pitch and Yamaha’s rigging manual on the full-throttle range.
How to test it
- Clean the hull and the prop, and load the boat the way you normally use it.
- Warm up the engine. Then run at full throttle, trimmed for the best speed.
- Hold full throttle until the rpm stops climbing. Note the highest steady rpm and the speed on your GPS.
- Look up the engine’s recommended full-throttle range in its manual, and compare.
Boat tachometers can be a few percent off. If the result is close to the edge of the range, check with a handheld tachometer.
What the published sea trials show
In November 2026 we checked the published outboard sea trials we hold against each engine's full-throttle range. None of the sea trials fell short of the range. About 74 % topped out inside it, and half of those in the top 10 % of the range. The other 26 % ran past the top, typically by 100 rpm.
Show the numbers
| Full-throttle rpm | Share of sea trials |
|---|---|
| Under the range | 0 % |
| Inside the range | 74 % |
| Above the range | 26 % |
So the test boats ran at the top of the range, not in the middle. Yours may not. A test is one boat on one day, with the load the tester chose. Yamaha’s rigging manual says a heavier load needs a smaller pitch to keep the right rpm at full throttle. If you copy a test boat’s prop, check your own rpm with your normal load.
How much does one inch of pitch change?
More pitch lowers full-throttle rpm, and less pitch raises it. Yamaha’s rigging manual puts one inch at about 150 rpm. Boating Magazine says about 200. Use it as a starting point, not a promise.
| Pitch change | Change in full-throttle rpm |
|---|---|
| 2 in less | 300–400 rpm more |
| 1 in less | 150–200 rpm more |
| 1 in more | 150–200 rpm less |
| 2 in more | 300–400 rpm less |
Example: Chris-Craft Launch 25 GT
On 16 December 2019, Mercury tested the Chris-Craft Launch 25 GT with two sets of counter-rotating props that differed only in pitch: 24 and 26 in. With 2 inches more pitch, the engine topped out 220 rpm lower (5,000 → 4,780 rpm). The boat went 0.6 knots faster (43.7 → 44.3 knots). That is 110 rpm an inch, less than the rule of thumb. More pitch only pays while the engine still reaches its range.
Reach the range with your normal load
Yamaha’s manual warns against running past the range: the engine can be damaged. Under the range, the engine labours, and Boating Magazine warns that on smaller engines this wears internal parts. A fouled hull or a full load pulls rpm down. So a prop that lets the engine only just reach the bottom of the range on a clean, light boat leaves no margin.
Inboard diesels follow the same rule. The maker gives a rated rpm for full throttle, and the engine should reach it with a normal load. Our inboard check works it out from the engine, the gearbox and the hull.
When it isn’t the prop
- The hull or the prop is fouled. Growth costs rpm and speed. Clean both and test again.
- The boat is heavier than usual. Test with the load you normally carry.
- The rpm rises, but the boat doesn’t speed up. The prop may be drawing air or slipping on its hub.
- The rpm has dropped slowly over the years. Have a mechanic check the engine.
- The rpm and the speed don’t add up. Check the tachometer with a handheld one.
Our guide to prop slip shows how to tell air from a slipping hub.
Check your prop in about a minute
Start with our outboard prop calculator or inboard prop calculator. Enter your full-throttle rpm. The free check tells you whether to go up or down in pitch, or to look at the hub, the tach or the engine first. It also gives the pitch and diameter range that fits your boat.
With Pro, a prop shop gets the exact size, and sees the full-throttle rpm of each prop it considers before the prop goes on.

Questions
How much pitch should I take off?
Divide the rpm you’re missing by 150–200. That gives roughly the inches of pitch to take off. If the engine is 400 rpm short of the range, about two inches is a start. The free check works it out for your boat and engine.
My engine hits the rev limiter. Is the prop too small?
Usually it has too little pitch. But a prop that draws air or slips on its hub also lets the engine rev without the boat speeding up. Check the prop before you buy a new one.
Is a few hundred rpm under the range OK?
No. Under the range, the engine works harder at full throttle than it should. Take off pitch until it reaches the range with your normal load.
How we worked it out
We compared each outboard sea trial’s full-throttle rpm with the range its outboard page shows. That is the maker’s recommended range, or for some Mercury engines the range Boating Magazine printed. Only sea trials on an engine with a published range count. The percentages count only those trials. We work the figures out again when we add sea trials.
Sources: Yamaha’s F70 rigging manual (pages 70 and 88) and Boating Magazine on prop pitch (2019). You’ll find the sea trials, with their sources, on our outboard pages.
All guides →